PRODUCTS

We offer a full range of fluid end expendables including valves and seats. Most of our fluid end parts are available for immediate delivery and are interchangeable with most other fluid ends.

Manufactured from the highest quality of steel, our products offer the highest performance and sturdiness in the market today, bringing about a superior primary concern for its users.

VALVE KEEPER

Our valves and valve seats are a reliable solution for high-pressure well service fracturing pumps, cementing pumps and mud pumps and have an extended life of 3-4 times. Valves are used to control the rate of flow in a line, to completely open a line, to completely shut off a line, or to serve as an automatic/semi-automatic safety device in oil & gas drilling processes.

Valve-keeper

HEADER RING

Increases packing set longevity 3-4 times. Resists extrusion and nibbling. Enhances resistance to abrasive material. Resists Explosive Decompression. Wipes plungers better, preventing solids from Wipes plungers better, preventing solids from embedding in the pressure rings. Maintains packing tension and pre-load resulting in better sealing as packing begins to wear.

HEADER RING

PLUNGER

Plungers pump the sand slurry mix out of the truck and into the well. To meet a variety of operations and customer needs, we offer multiple coatings to withstand wear and tear. Our customers can choose from a chrome coating, a tungsten carbide coating or an armor coating. We only offer solid plungers, eliminating any chance for failure that may occur with a hollow plunger.

10PLUNGER

OIL & GAS FRACKING SEALS

Available in a variety of sizes and configurations demanded by the industry, our fracking seals provide excellent performance even within the harshest of environmental and operating conditions.

7PACKING NUT SEAL

SPRING

Compression spring ends often are ground to increase operational life and to allow the spring to sit squarely on the load-bearing surface. Grinding of compression springs also increases the number of active coils and the wire diameter available in a given volume of space, which can result in higher loads or lower stresses.

12SPRING

PRESSURE RINGS

As exploration and production of oil and gas reserves go deeper and hotter, sealing technologies must keep pace to withstand increasingly hostile conditions for longer periods of time.

11PRESSURE RINGS

TEP rings extend seal life by preventing extrusion of elastomeric seals in high pressure, high temperature environments. Under high pressure, the elastomer seal applies an axial force on to the wedged back-up set.

PLUNGER CLAMP

The Plunger clamps have a straight line action. The clamps are either base mounted or nose mounted and can be threaded directly into the fixture or mounted by means of mounting bracket. The clamps range from light to heavy duty with a range of clamping strokes and are suitable for pushing components into position. The clamps toggle in both forward and rear positions.

9PLUNGER CLAMP

LATERN RING

Lantern Rings are normally used by pumps that use some type of liquid to operate. The Lantern Ring goes around a rotating shaft, with the opening on the side of the Lantern Ring designed to allow lubrication of oil, grease, or even water to be shot through to the bearing surface. This unique design allows for easy maintenance to the pumps without disassembly of the entire pump.

6LANTERN RING

JUNK/SPACER RING

Junk rings, lantern rings, and adapters are required to fill the are required to fill the excess space inside the stuffing box. Some of the spacers are drilled or grooved to allow lubrication to allow lubrication to reach the packing.

4JUNK RING

FEMALE ADAPTER

A female top adapter constructed from PEEK, an engineered plastic is available. This adapter supports the pressure This adapter supports the pressure ring and eliminates lantern ring cracking from very high discharge pressures.

3FEMALE ADAPTER

D-RING

This is designed for the oil industry and more specifically for the worker who operates on the monkey board. It includes added options for connection to the derrick belt and provides the worker with fall protection and comfort with the large frontal pad while positioning for the next drilling pipe.

2DRING

SUCTION CUP

A suction cup, also known as a sucker, is an object that uses the negative fluid pressure of air or water to adhere to nonporous surfaces, creating a partial vacuum.

1suction cap